Person:
GÜMÜŞ, METİN

Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

OrgUnit Logo
Organizational Unit

Job Title

Last Name

GÜMÜŞ

First Name

METİN

Name

Filters

2011 - 20133
Reset filters

Settings

Subject: Biodiesel ×

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    PublicationMetadata only
    Impact of compression ratio and injection parameters on the performance and emissions of a DI diesel engine fueled with biodiesel-blended diesel fuel
    (PERGAMON-ELSEVIER SCIENCE LTD, 2011) SAYIN, CENK; Sayin, Cenk; Gumus, Metin
    This work investigates the influence of compression ratio (CR) and injection parameters such injection timing (IT) and injection pressure (IP) on the performance and emissions of a DI diesel engine using biodiesel (%5, 20%, 50%, and 100%) blended-diesel fuel. Tests were carried out using three different CRs (17, 18, and 19/1), ITs (15 degrees, 20 degrees, and 25 degrees CA BTDC) and IPs (18, 20 and 22 MPa) at 20 N m engine load and 2200 rpm. The results showed that brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and nitrogen oxides (NOx) emissions increased while brake thermal efficiency (BTE), smoke opacity (OP), carbon monoxide (CO) and hydrocarbon (HC) decreased with the increase in the amount of biodiesel in the fuel mixture. The best results for BSFC, BSEC and BTE were observed at increased the CR, IP, and original IT. For the all tested fuels, an increase in IP, IT and CR leaded to decrease in the OP. CO and MC emissions while NO emissions increase. (C) 2011 Elsevier Ltd. All rights reserved.
  • No Thumbnail Available
    PublicationMetadata only
    The impact of fuel injection pressure on the exhaust emissions of a direct injection diesel engine fueled with biodiesel-diesel fuel blends
    (ELSEVIER SCI LTD, 2012) SAYIN, CENK; Gumus, Metin; Sayin, Cenk; Canakci, Mustafa
    In this study, the effects of fuel injection pressure on the exhaust emissions and brake specific fuel consumption (BSFC) of a direct injection (DI) diesel engine have been discussed. The engine was fueled with biodiesel-diesel blends when running the engine at four different fuel injection pressures (18, 20, 22, and 24 MPa) and four different engine loads in terms of mean effective pressure (12.5, 25, 37.5, and 50 kPa). The results confirmed that the BSFC, carbon dioxide (CO2), nitrogen oxides (NOx) and oxygen (O-2) emission increased, smoke opacity, unburned hydrocarbon (UHC) and carbon monoxide (CO) emissions decreased due to the fuel properties and combustion characteristics of biodiesel. On the other hand, the increased injection pressure caused to decrease in BSFC of high percentage biodiesel-diesel blends (such as B20, B50, and B100), smoke opacity, the emissions of CO, UHC and increased the emissions of CO2, O-2 and NOx. The increased or decreased injection pressure caused to increase in BSFC values compared to original (ORG) injection pressure for diesel fuel and low percentage biodiesel-diesel blends (B5). (C) 2011 Elsevier Ltd. All rights reserved.
  • No Thumbnail Available
    PublicationMetadata only
    Influence of injector hole number on the performance and emissions of a DI diesel engine fueled with biodiesel-diesel fuel blends
    (PERGAMON-ELSEVIER SCIENCE LTD, 2013) SAYIN, CENK; Sayin, Cenk; Gumus, Metin; Canakci, Mustafa
    In diesel engines, fuel atomization process strongly affects the combustion and emissions. Injector hole number (INHN) particular influence on the performance and emissions because both parameters take important influence on the spray parameters like droplet size and penetration length and thus on the combustion process. Therefore, the INHN effects on the performance and emissions of a diesel engine using biodiesel and its blends were experimentally investigated by running the engine at four different engine loads in terms of brake mean effective pressure (BMEP) (12.5, 25, 37.5 and, 50 kPa). The injector nozzle hole size and number included 340 x 2 (340 mu m diameter holes with 2 holes in the nozzle), 240 x 4, 200 x 6, and 170 x 8. The results verified that the brake specific fuel consumption (BSFC), carbon dioxide (CO2) and nitrogen oxides (NOx) emission increased, smoke opacity (SO), hydrocarbon (HC) and carbon monoxide (CO) emissions reduced due to the fuel properties and combustion characteristics of biodiesel. However, the increased INHN caused a decrease in BSFC at the use of high percentage biodiesel diesel blends (B50 and B100), SO and the emissions of CO, HC. The emissions of CO2 and NOx increased. Compared to the original (ORG) INHN, changing the INHN caused an increase in BSFC values for diesel fuel and low percentage biodiesel-diesel blends (B5 and B20). (C) 2013 Elsevier Ltd. All rights reserved.