Person: GÜNDÜZ, OĞUZHAN
Loading...
Email Address
Birth Date
4 results
Search Results
Now showing 1 - 4 of 4
Publication Open Access Fabrication of Amphotericin-B-loaded Sodium Alginate Nanoparticles for Biomedical Applications(2022-12-01) ULAĞ, SONGÜL; ŞENGÖR, MUSTAFA; GÜNDÜZ, OĞUZHAN; ULAĞ S., Celik S. E., ŞENGÖR M., GÜNDÜZ O.In this study, amphotericin-B (AMB)-loaded sodium alginate (SA) nanoparticles were fabricated using the electrospraying technique for biomedical applications. AMB is an antifungal agent and is poorly absorbed from the gastrointestinal tract due to its low aqueous solubility. Therefore, it should be given parenterally to treat systemic fungal infections. This study aims to transport it with nanoparticle formulations and observe the nanoparticle release behaviours. Scanning electron microscopy (SEM) images showed that nanoparticles of 0.5% SA fabricated at 37 kV had the most suitable particle diameter (93.36±24.386 nm) for loading 0.5, 1, and 3 ml of AMB. Fourier transform infrared spectroscopy (FTIR) results demonstrated that AMB successfully loaded into 0.5% SA nanoparticles. Drug release behaviours of the AMB-loaded particles indicated that AMB was released with a burst at the beginning, and release behaviour became sustainable after half an hour. The encapsulation efciencies of the diferent amounts of drug were calculated, and the results showed that the highest encapsulation efciency belonged to the 0.5% SA/1 AMB nanoparticles (42±1.23%).Publication Open Access Fabrication and in vitro characterization of polycaprolactone/graphene oxide/collagen nanofibers for myocardial repair(2023-01-01) ULAĞ, SONGÜL; ŞAHİN, ALİ; DUMLUDAĞ, FATİH; GÜNDÜZ, OĞUZHAN; Karapehlivan S. S., Danisik M. N., Akdag Z., Yildiz E. N., Okoro O. V., Nie L., Shavandi A., ULAĞ S., ŞAHİN A., DUMLUDAĞ F., et al.This study is focused on fabricating tissue-engineered electrospun nanofibers that contain polycaprolactone (PCL), graphene oxide (GO), and collagen (COL) to get an alternative treatment for cardiac injuries. GO (1.5 wt%) is used to support the contraction-elongation of cardiomyocytes by improving electrical stimulation. The COL (1, 3, and 5 wt%) is the main component of the myocardial extracellular matrix have led to their frequent use in cardiac tissue engineering (CTE). The scanning electron microscope (SEM) images show the homogeneous and bead-free morphologies of the nanofibers. Adding a high amount (3% and 5%) of COL decreases the tensile strength value of 17% PCL/1.5% GO nanofiber. 3-(4,5-Dimethylthiazol-2-yl)-2,5-Diphenyltetrazolium Bromide (MTT) assay demonstrates that the COL addition increases cell viability compared to that in 17% PCL/1.5% GO nanofibers on the third day. The response of the nanofibers to alternating current (AC) signal is studied between the frequencies 40 and 105 Hz. The direct current (DC) conductivity values of the films are determined to be between 1.10−10 and 6.10−10 S m−1 at 25 °C. The AC conductivity values show frequency-dependent behavior. Among the PCL/GO-based electrospun nanofibers, 17% PCL/1.5% GO/5% COL nanofiber shows greater DC and AC conductivity than 17% PCL/1.5% GO nanofiber.Publication Metadata only Gel-Inks for 3D printing in corneal tissue engineering(Springer, 2021-01-01) ŞENGÖR, MUSTAFA; EKREN, NAZMİ; GÜNDÜZ, OĞUZHAN; Ulağ S., Cesur S., DOĞAN E., ŞENGÖR M., EKREN N., ÜSTÜNDAĞ C. B., GÜNDÜZ O.Publication Open Access Fabrication Strategies for Bioceramic Scaffolds in Bone Tissue Engineering with Generative Design Applications(2024-07-01) KURT, MUSTAFA; GÜNDÜZ, OĞUZHAN; Cinici B., Yaba S., KURT M., Yalcin H. C., Duta L., GÜNDÜZ O.The aim of this study is to provide an overview of the current state-of-the-art in the fabrication of bioceramic scaffolds for bone tissue engineering, with an emphasis on the use of three-dimensional (3D) technologies coupled with generative design principles. The field of modern medicine has witnessed remarkable advancements and continuous innovation in recent decades, driven by a relentless desire to improve patient outcomes and quality of life. Central to this progress is the field of tissue engineering, which holds immense promise for regenerative medicine applications. Scaffolds are integral to tissue engineering and serve as 3D frameworks that support cell attachment, proliferation, and differentiation. A wide array of materials has been explored for the fabrication of scaffolds, including bioceramics (i.e., hydroxyapatite, beta-tricalcium phosphate, bioglasses) and bioceramic–polymer composites, each offering unique properties and functionalities tailored to specific applications. Several fabrication methods, such as thermal-induced phase separation, electrospinning, freeze-drying, gas foaming, particle leaching/solvent casting, fused deposition modeling, 3D printing, stereolithography and selective laser sintering, will be introduced and thoroughly analyzed and discussed from the point of view of their unique characteristics, which have proven invaluable for obtaining bioceramic scaffolds. Moreover, by highlighting the important role of generative design in scaffold optimization, this review seeks to pave the way for the development of innovative strategies and personalized solutions to address significant gaps in the current literature, mainly related to complex bone defects in bone tissue engineering.